The toilet is not professionally installed and the flange is not installed.
Long-term use causes the toilet to loosen with the ground.
The quality problem of the toilet, there are cracks in the ceramics.
Internal parts of water tank are aging.
There is something wrong with the water inlet group or the water outlet group of the toilet.
Solution:
If the internal parts of the water tank are aging, they need to be replaced as soon as possible. If the joint between the toilet and the sewer leaks, the toilet needs to be reinstalled and resealed. If there is a crack in the toilet itself that causes water leakage, it is best to replace it with a new one. If there is a problem with the water inlet group and the water outlet group of the toilet, you need to open the water tank and see that the water tank overflows. The water flowing out of the water pipe indicates that the water inlet group is broken. If there is a sound of water inlet, it indicates that the water outlet group is broken. If the water tank leaks, you can remove the launcher and clean up the scale. After eliminating the above problems, it is water seepage caused by improper installation:
1, if it is installed in a specialty store, it is usually filled with a sealing ring, and the toilet is surrounded by glass glue; Tools to be prepared: art knife, water tape, wrench, glass glue, glass glue gun. Special sealing ring for toilet (if removed, it needs to be replaced)
2. If it is a refurbished hydropower tool, white cement will generally be used; Tools prepared: a screwdriver (used to remove the original white cement) and white cement (when reinstalling, first mix water at the bottom of the toilet, then put the toilet seat on it to stabilize it, then seal the toilet foot pad with the mixed white cement, and it can be used when it is dry. Be careful not to let white cement fall into the pipeline when loading, otherwise it will cause pipeline blockage.
If the above methods still can't solve the water seepage problem, you can only find professional maintenance personnel.
Toilet is a passage for discharging dirt, and it is also something we must use every day. If you don't do a good job of cleaning at ordinary times, it is likely to become the chief culprit threatening your health. Many people think it is difficult to clean the toilet, but they are actually learned.
① vinegar descaling method: pour the mixed solution of vinegar and water into the toilet, soak for half a day, and brush off the scale with a brush.
② Sandpaper descaling method: Rubbing toilet dirt with the finest sandpaper can remove dirt that cannot be removed by detergent.
3 baking soda descaling: sprinkle baking soda in the toilet, then brew with hot water for half an hour, and the dirt can be brushed off.
(4) Decontamination method with bleaching powder solution: firstly wipe with bleaching powder solution, and then rinse with water.
5. Self-made small brush to scrub the toilet: the toilet produces yellow dirt, which is difficult to clean with a brush. Waste nylon stockings can be tied to one end of a stick and scrubbed with foaming cleaner. After 1 month, the toilet will remain white.
⑥ Detergent: First, put a proper amount of water in the toilet, and wash it once with a toilet brush, then pour in 5- 10 ml of detergent or hydrochloric acid solution and brush it evenly with a brush. If the dirt is heavy, you can soak it in a little detergent and brush it until it is clean. Hydrochloric acid is very corrosive. If cleaning with hydrochloric acid, pay attention to safety and don't splash on the skin.
I suggest you choose the products of Oriental Yuhong.
Yuhong brand plugging treasure (quick setting)
Yuhong brand plugging treasure (quick setting) is a powdery waterproof plugging material made of special cement and additives through a special process. It can be used for waterproofing and plugging leakage or gushing basement, and can be used for construction with water.
There are three main forms of water leakage in general waterproof projects, namely, point leakage, joint leakage and surface leakage. According to the specific situation of water leakage in the project, quick-setting waterproof and plugging treasure can be used, and different water stopping and plugging technologies can be used to deal with it.
1, water leakage hole is waterproof and plugging.
Waterproof treatment of the parts around the leaking hole. Use powder: water = 1:0.35, mix the powder with water, and apply it around the leakage hole. Generally use a trowel or scraper for 2~3 times, and the material used each time is about 1.2Kg/m2. After each coating is hardened (without fingerprints), spray it wet (but without water), and then proceed to the next step of construction.
Pick up the annular groove to stop the leakage. Centering on the water leakage point, carve a groove (the groove diameter × depth is 10mm×20mm and 20mm×30mm, and the general capillary seepage carves a round hole with a diameter of 10mm), and rinse the groove with water. Mix the powder with water and knead it into a cone with a diameter close to that of the tank. When it feels hard by hand, put it into a jar, squeeze it with a wooden stick, tap it to make the inside and the surrounding area solid and dense, and then stop the water instantly.
2. Waterproofing and plugging of leaking cracks
Waterproof treatment of parts around water leakage cracks. Use powder: water = 1:0.35, mix the powder with water and apply it around the leaking gap. Generally use a trowel or scraper for 2~3 times, and the material used each time is about 1.2Kg/m2. After each coating is hardened (without fingerprints), spray it wet (but without water), and then proceed to the next step of construction. Lift the splayed groove for plugging. Dig a splayed groove with a depth of 10mm~30mm and a width of 15mm~50mm along the crack. Put a small rope along the crack at the bottom of the cylinder. The length of the rope is about 200 ~ 300 mm After mixing the powder with water, knead it into strips and leave it for a while. When it feels hard by hand, fill it in the groove where the rope is put, quickly compact the edge, then pull out the rope and compact it again to make the water leak out along the rope hole. For longer cracks, they can be filled step by step, and the length is about 100mm~ 150mm, with a gap of 20mm wide for each gap. At the gap of 20mm, when the mixture is about to solidify, insert the nail wrapped with the mixture into the gap and quickly compact the gap around the nail with the mixture. At the same time, rotate the nail and pull it out immediately to make water flow out along the nail hole. After the sealing material is solidified, the nail hole is treated according to the waterproof sealing method of the leaking hole.
3, large area leakage treatment method
When plugging, water must be diverted to relieve pressure first. The principle of water diversion is to change surface leakage into line leakage and point leakage, reduce the leakage parts as much as possible, and concentrate the leakage at one point or several points to reduce the seepage pressure at other parts. After that, waterproof and plugging shall be carried out according to the treatment method of point leakage or line leakage.
Water Lipton efficient flexible waterproof slurry
Water Lipton high-efficiency flexible waterproof slurry is a two-component water-based waterproof slurry composed of high-quality acrylate emulsion, various additives and inorganic powder composed of special cement and various fillers in a certain proportion. When coated on the surface of the substrate, a flexible and high-strength waterproof coating film can be formed after curing.
Haoshitu 100 High Elastic Thickness Acrylic Waterproof Coatings
Haoshitu 100 high elastic thickness acrylic waterproof coating is a thick one-component waterborne polymer waterproof coating based on high-quality modified acrylate multi-polymer emulsion, with a variety of additives and fillers. The coating has the characteristics of low temperature resistance and high elongation.
Castrol 100 Polymer Cement Waterproof Coatings
Christie's 100 polymer cement waterproof coating is a two-component water-based waterproof coating made of high-quality modified polymer emulsion and cement as main raw materials, adding various additives and fillers, and through scientific processing. It has the characteristics of high tensile strength and firm combination with matrix.
SPU-30 1 one-component polyurethane waterproof coating
"Yuhong" brand SPU-30 1 one-component polyurethane waterproof coating is a one-component moisture-cured waterproof coating, which reacts with moisture in the air after construction to form a flexible, durable and seamless elastic waterproof coating.