The installation time of the bathroom is generally selected when the decoration is about to be completed. The reason is very simple, to avoid bumping or soiling the toilet during construction. Before installation, of course, the product should be inspected to confirm whether there are any accessories missing or damaged. Open the cover of the water tank and learn about the water parts inside. They are not lacking.
How to install the toilet
1, take out the pipe plug of the ground sewer, check that there is no sundries in the pipe, and clean up around the nozzle.
2. Align and straighten the water outlet pipe of the toilet, draw a mark on the bolt hole of the toilet, and remove the toilet.
3. Make a hole with a diameter of 20 mm and a depth of 60 mm at the mark, insert the bolt with a diameter of 10 mm into the hole, screw it firmly with cement, put the toilet eye on the bolt to make it match the mark, and remove the toilet after the test. Apply putty around the water outlet and sewer of the toilet, then align the four bolt holes of the toilet with the bolts, align them evenly, cover the bolts with rubber pads, and screw on the nuts until the tightness is moderate.
4. Aim at the center of the rear tail of the toilet, draw a vertical line, draw a horizontal line at a height of 800 mm from the ground, draw a mark on the horizontal line according to the position of the two side holes on the back of the water tank, and make a hole with a diameter of 30 mm and a depth of 70 mm at the printed hole. Insert a bolt with a diameter of 10 mm and a length of 100 mm into the hole and tighten it with cement. Hang the back water tank on the bolt and align it evenly, especially with the center of the toilet. Put a rubber pad on the bolt and screw on the nut until it is moderately elastic.
5. When installing the sewer elbow of the rear water tank, first remove the nuts of the sewer outlet of the rear water tank and the water inlet of the toilet, put them back to back on the sewer elbow, and put the rubber pads on the sewer pipes respectively. Insert the upper end of the water elbow into the water outlet of the rear water tank and the lower end into the water inlet of the toilet, then push the rubber pad to the water outlet, screw on the nut, straighten the water elbow, and screw it with pliers until it is moderately elastic.
6. When connecting the water supply with a splayed door, measure the size of the drift door of the water tank from the nozzle of the water supply, match the threaded joint, install the splayed door and put it into the nozzle of the water supply. Cut the copper pipe or plastic pipe, and bend the fork appropriately. Then put the nuts of the floating door and the splayed door back to back on the copper pipe or plastic pipe, wrap the asbestos rope or lead oil hemp thread on both ends of the pipe, insert them into the entrances and exits of the floating door and splayed door respectively, and tighten the nuts.
Installation mode and installation price of toilet
The installation cost of the toilet will vary according to different regions, and the general price is around 100 yuan. In order to save trouble in future life, I suggest you ask a professional to install the toilet.
1. Before installation, conduct a comprehensive inspection of the sewage pipeline to see if there are dirt, sand, waste paper and other sundries in the pipeline. At the same time, check whether the floor where the toilet is installed is flat. If the ground is uneven, level the ground when installing the toilet. Saw the lower drain pipe short, and make the lower drain pipe 2mm-5mm higher than the ground as far as possible when conditions permit.
2. Before choosing a toilet, first determine the size of the toilet at home, and then choose your favorite style according to the size.
3. Before installing the toilet, make sure that the products, accessories and instructions you choose are complete, and read the instructions carefully to understand some product matters.
4. Sewers need to be handled smoothly by installers. The outlet at the bottom of the toilet should be equipped with a special flange for the toilet, or the glass glue should be evenly coated on the sewer. Glue should be applied at the bottom and around the toilet, and the gap between the toilet and the wall should be even, correctly placed and flat.
5. After the toilet is in place, it is required to be watertight, the water level is correct, the flushing is smooth, the switch is flexible, and the cover is stable.
6. At present, it is generally not necessary to install the anchor screws when installing the toilet, but the reserved holes on the toilet should be blocked with glass glue to prevent the odor from turning out.
7. If the anchor bolt is installed, first use the special sealant installed in the toilet seat to evenly spread it around the drain outlet of the toilet seat 2CM. The drain of the toilet seat should face the center of the drain pipe. Draw the position of the expansion bolt on the left and right sides of the toilet seat, remove the toilet seat, punch holes and bury the expansion bolt. It should be noted that this newly punched expansion bolt may break the waterproof layer. It is suggested that the expansion bolt should be filled around the hole when it is buried. Then bury the expansion bolt, screw on the expansion bolt first, so that the expansion bolt can be completely loosened to reinforce its tension, then unscrew the upper screw, put the toilet seat away, and then screw on the screw directly and cover it to keep the whole place beautiful. At the junction of the toilet and the ground surface, because the toilet and the ground surface are not integrated, the external mouth of the toilet can be stirred and sealed with caulking agent and transparent sealant to maintain its integrity with the ground surface, and local toilet water can also be blocked from the periphery of the toilet.
8. After the toilet is installed, it cannot be put into use until the glass glue (putty) or cement mortar is cured. The curing time is generally 24 hours.
9. Finally install or debug the water tank fittings.