When fishing, what do you need to pay attention to if you want to fundamentally solve the problem of sub-line entanglement?
For every fisherman, the most annoying thing during fishing is the floating of small fish, and the second is that the sub-line is entangled back and forth, especially for beginners who are just learning to fish and are relatively frugal. , the sub-wire is tangled and I don’t want to replace it directly. I have to laboriously connect the sub-wire every time, which is very annoying! Especially for older fishing friends with poor eyesight, the new sub-line that has just been untied or replaced can get tangled again after only a few casts, which is a headache.
I often receive private chats with many fishing friends, and we are all looking for good ways to prevent sub-line entanglement. Many fishing friends will also use special binding methods or rely on external factors to reduce sub-line entanglement, but they still cannot fundamentally solve the problem. In fact, if you want to fundamentally solve the problem of sub-wire winding, you only need to pay attention to the following points! 01 Rod Throwing Technique
When throwing the rod, we should try to keep the main line in a parallel state, and it is best to throw in a swing. Do not bend the rod slightly and pop it out directly. This will cause the initial speed to be too fast and difficult to control. It will easily cause rebound and the sub-line will easily get entangled. 02 Throw the rod full
We throw the rod full, and then pull back some, first tie the toad, let the main line carry the force, and wait until the float slowly drops, then we press the water level. This will greatly reduce the chance of sub-wire entanglement. 03 The lead skin seat should be as long as possible
The longer the lead skin seat is, the lower the number of turns of the rolled tin pendant will be. It is also possible to roll the tin pendant as rounder and closer as possible, and cut it when fishing and adjusting the drift. When repairing the tin pendant, it must be cut vertically, and the two sides of the tin pendant should be scraped into a tapered shape as much as possible, so that it will not be easy to rotate when throwing the rod into the water or lifting the rod. 04 There are too many jumps in the main line, and the sub-lines should not be too long
The main line must be matched appropriately. Don’t make the main line too thick and the sub-lines too thin. The thinner the sub-line, the weaker the Pisces will be. Very easy to wrap. We all know that when fishing, the longer and thinner the sub-line, the easier it is to get entangled. 05 The figure-of-eight ring must be well bolted
When we choose the figure-of-eight ring, we should try our best to use the figure-of-eight ring with stronger coaxiality and rotational speed. The connection between the figure-eight ring and the main line must be in the same boat. After the thread ends are processed, the thread knot must be wrapped with a floating seat or an anti-tangle bean. When buying a floating seat, be sure to buy a better one. Don’t buy a bad one, otherwise you will have a headache. 06 Bait pulling technique
When using bait fishing, it is best not to stick the baits together. Pay attention to the technique and separate the head line before throwing the rod. 07 The fishing adjustment is too blunt
The float should not be adjusted too bluntly. When there are too many small miscellaneous fish in the water, they will eat hooks and compete for food, and they will easily get entangled. If the float moves, the rod must be lifted in time. If you want to catch blunt fish, try to shorten the head line as much as possible. 08 Fish Stinging Techniques
When stinging a fish with a stick, we must exert force with our wrists and an inch of force. After the fish is stung, apply force slowly. If the fish is not caught, the lead should be removed before the lead falls out of the water. Remove force. Never let someone lift the pole recklessly and let the double hooks of the lead pendant directly discharge the water, as this is the most likely to happen. 09 The lead seat float should not be fixed
There should always be a gap of about one millimeter between the float seat and the space bean. The float and the float seat must not be locked. Once locked, they cannot rotate at will, and Very easy to tangle. 10Choose the main line with low ductility
The main line must not be very malleable, otherwise the main line will be stretched if it is used by a big fish, walks fish for a long time, or is pulled by the bottom. It will be bad for us to cast the pole, and it will easily cause the line to get tangled. 11. Sub-threads should not be used. The size of the hook must be matched appropriately
When tying hooks, the size of the sub-thread and the size of the hook must be reasonably matched. Do not use particularly thin sub-threads to tie particularly large hooks. Do not use particularly thick sub-threads to tie particularly small hooks. 12. The selection of small parts must be reasonable
The parts of the alignment set must be suitable. Do not choose poor ones. Choose a floating seat with high coaxiality and moderate tightness, especially the lead sheet. The smaller the diameter of the seat and the aperture gap of the main line, the better. I personally suggest that it is best to choose matching parts, but they are a little expensive.
13 Summary
If we want to better solve the problem of sub-line winding, we must start from ourselves. Whether it is our throwing technique or every small accessory, we must pay attention to details. Only details can determine Make or break!