(1) The construction can be started only after the line is drawn on site according to the drawing position and approved by the supervision unit.
(2) Installation of frame system
1) installation of ground rail: according to the lofting position, put the ground rail in an appropriate position, reserve the position of doors and corners, nail it firmly with air nails every 100cm and fix it on the floor. If the floor is ceramic tile or stone, turn the hole with an electric drill, then bury the plastic plug and fix the ground rail with screws. The length of grounding rail must be controlled within ±65438±0mm/m/m.
2) Installation of the sky rail: scan the ground rail with a spirit level, place the sky rail under the floor or ceiling in parallel, and then fix it with air nails or tail screws. The height difference should be cut to 45 degrees, the joint should be smooth, and the gap should be less than 0.5 mm.
3) Installation of straight rods: Install straight rods at intervals indicated or required by drawings or construction instructions (in general standard specifications, the interval between straight rods is 100cm), insert straight sliding rods above the straight rods, lap them on the inside of the crown block track, and fasten them reversely. When the straight rods are lowered, slide them above the height adjusting screws.
4) Install the cross bar: insert both ends of the cross bar into the preset fixing holes of the left and right straight bars and fix them upside down. The first bar below will be upside down, and the rest will be upside down. If the specification is not standard, cut off the middle part of the cross bar, insert cross slide bars at both ends, adjust it to the required size, and fix it by drilling tail screws. Then put it on a straight pole. After the installation of straight bars and cross bars is completed, scan with a spirit level to adjust the level of all straight bars (the standard height of skirting board is 80mm).
5) Two-way corner column installation:
At the corner of the carriage, two-way corner posts must be erected, and their length must be grounded and connected with the sky rail. L-shaped fixing parts are fixed in the ground rail groove with air nails and on the overhead rail with drill tail screws.
6) Installation from scratch:
When the steel plate or glass panel is connected to the wall, or the calcium silicate wall, gypsum board wall, wooden wall or T-shaped wall is connected to the steel plate, and it must be of standard size, it should start with the word. In application, drill holes with electric drill, bury plastic plugs every 90cm, and then fix them with screws.
7) Eight-character startup installation:
When the compartment is T-shaped, or is connected with the glass frame of the glass panel in a cross shape, or is connected with two groups of door leaves in a T shape, it is treated as a figure of eight from the beginning, and its fixing method is to lock it on the frame of the panel every 90cm with drilling screws.
8)U-shaped closed head:
If the end of the steel plate is connected with a reinforced concrete wall or a cement column, it shall be treated with a U-shaped head and nailed or spaced with an air nail.
Drill a 90m hole with an electric drill, bury the plastic plug and tighten it.
(3) Panel system installation
1) Steel plate: stand the panel upright, with the lower end against the skirting cover, so that both sides of the panel are placed in the center of the straight rod, and slowly push the panel against the frame, then buckle the panel batten between the grooves of two steel plates, and lock the panel batten on the straight rod of the frame with drilling screws, and fix a screw every 30cm. Pay special attention to the vertical and horizontal when assembling. If the size is non-standard, the end plate is connected with the reinforced concrete wall.
2) Glass panel: The installation method is the same as that of steel panel. If it is a low glass or semi-glass panel, put the glass panel above the steel plate, then fix it with metal battens and lock it with drilling screws. If there are additional aluminum transverse shutters, they must be fixed with a single-sided glass panel and then used as shutters. After the plastic is injected, transferred and inserted into the rotating rod on the louver, the PVC plastic film inside the glass is removed, and then the other glass panel is fixed (water, electricity and air conditioning pipelines must be installed in advance before application).
3) Aluminum plate: aluminum fasteners are placed at the left and right ends of the aluminum plate and fixed on the frame according to the installation method of steel plate (water, electricity and air conditioning pipelines must be installed in advance before construction).
4) Door leaf panel:
First, insert the PVC cushion into the groove of the door frame and cut it into appropriate length. Then, insert the door frame into the straight bar and cross bar, and fix the door frame and panel with drilling screws. Then, install hinged door pieces on the door frame to ensure the spacing and stability, and install and fix the horizontal lock, door stop and door bow device after the switch is noiseless.
(4) Late construction
1) Gridline layering: After all the panels of the panel are installed, they can be used as the layering of the panel. Cut the layering neatly and have the same height as the panel, and knock it into the joint of the panel layering with coarse glue to ensure that it is fully embedded.
2) Shutter adjusting knob: After the parting line layering is completed, insert the adjusting knob into the hexagonal screw of the shutter adjusting piece.
Lock M4 nut and cover it.
3) Opening of socket and switch: According to the preset position of mushroom base and switch, mark 5cm×9cm with a pencil, drill a round hole of 10mm at the four corners, and then saw it with a vertical wire saw.
(5) Clean up and tear off the protective film on the watch board, clean up the garbage, take all the garbage back and transport it away from the construction site, and wipe the watch board with handprints or dust, and the construction is completed.