1. How to install the toilet
1. Check the levelness between the sewage pipe and the ground
First of all, when installing the toilet, we need to have an overall view of the sewage pipe, check whether there is blockage of debris such as sediment in the pipe, and at the same time, check carefully whether the ground around the toilet is level. If the floor is uneven, we need to level the ground before installing the toilet.
2. Determine the sewage pipe center
I believe everyone knows that the toilet has a sewage pipe center, and before installing the toilet, it is necessary to determine its sewage pipe center. We can turn the toilet upside down, and then determine the center of the toilet outlet. At this time, draw a cross center line at its center, and the cross center line will extend to the bottom of the toilet and the feet around it.
3. Fixing the toilet
Through the above two steps, the next step is to fix it. When fixing the toilet, first align the crosshair on the toilet with the ground sewage outlet, and when ensuring the horizontal installation of the toilet, press the sealing ring hard, and finally install the anchor screws and decorative caps.
4. To seal the bottom
It is necessary to install some corresponding sealing rings on the sewage outlet, such as coating a circle of glass glue (putty) or cement mortar around it, and the ratio of cement to sand is 1:3.
5. Install water tank fittings
Finally, install water tank fittings. We can put water for 3 to 5 minutes to flush the pipeline first. After ensuring that the tap water pipe is clean, you can install the angle valve and the connecting hose, and then connect the hose with the installed water tank fittings to ensure that the water source can be connected.
6. Debugging and inspection
In order to ensure the successful installation, it is necessary to re-inspect the toilet, not only to see whether the inlet valve and seal are normal, whether the installation position of the drain valve is flexible, whether there is blockage and leakage, but also whether the inlet valve is equipped with a filtering device.
2. How to install the toilet
1. First, we need to take out the pipe plug of the ground drain, check whether there are any sundries piled up in the pipe, and then clean the nozzle.
2. Align the outlet pipe of the toilet with the outlet pipe, then put it straight. Finally, draw a mark on the bolt hole of the toilet, and then remove the toilet.
3. At the place where we marked, punch a hole with a diameter of 15-2mm and a depth of 6mm, then insert a bolt with a diameter of 1mm into the mouth, screw it firmly with cement, tighten the bolt for the toilet eye to match the mark, and remove the toilet after the test. Apply putty around the toilet outlet and sewer pipe, then align the four bolt holes of the toilet with the bolts, put them straight, cover the bolts with rubber pads, and screw the nuts until the tightness is moderate.
4. aim at the center of the toilet, draw a vertical line, draw a horizontal line at a height of 75mm from the ground, make a mark on the horizontal line according to the position of the two side holes on the back of the water tank, and punch holes with a diameter of 3mm and a depth of 7mm at the printed hole. Insert a bolt with a diameter of 1mm and a length of 1mm into the hole and twist it firmly with cement. Hang the back water tank on the bolt, put it straight, pay special attention to the center of the toilet, put a rubber pad on the bolt, and screw the nut until it is moderately elastic.
5. When installing the water elbow under the back water tank, first remove the nuts of the water outlet of the back water tank and the water inlet of the toilet, and put them on the upper part of the water elbow back to back, and the rubber pads are also put on the water pipes respectively. Insert the upper end of the water elbow into the water outlet of the back water tank and the lower end into the water inlet of the toilet, then push the rubber pad to the water outlet, screw on the nut, straighten the water elbow and screw it to the right position with pliers.
6. finally, when we connect the water supply with the splayed door, we should first measure the distance between the water tank drift door and the water supply nozzle, match the nipple, install the splayed door and put it into the water supply nozzle. Cut off the copper pipe or plastic pipe, and bend the lamp fork properly. Then, put the float door and splayed door nut back to back on the copper pipe or plastic pipe, wrap oil asbestos rope or lead oil hemp thread at both ends of the pipe, insert them into the import and export of the float door and splayed door respectively, and tighten the nuts. The toilet can be installed when it is finished.
how to install the toilet? If it is necessary to install the toilet, you can complete it step by step. If you have no relevant experience, you can't do it well. How to install the toilet? The installation of flush toilets is similar to other types of toilets. It is recommended that anyone who does not understand the installation should be handed over to professionals.